1 ultrasonic cleaning machine
Please reference ultrasonic cleaning machine instructions, cleaning machine, electric control cabinet between the host and the temperature control sensor signal wire connection, ultrasonic drive line, heater control line line, and connect the 380VAC power, washing machine water pipe, a water outlet pipe and an overflow discharge tube.
2 ultrasonic cleaning machine water
To clean the pool to participate in the appropriate amount of water, the level of immersion will be immersed in the parts to be cleaned, the general does not exceed 3/4 of the cleaning po
3 ultrasonic cleaning machine heating
Start the electric control heating switch, the water temperature adjustment knob on the white scale line points to the appropriate temperature (should be about 60 degrees Celsius). Cleaning machine in the process of use, the maximum temperature of the cleaning agent should not exceed 70.
4 ultrasonic cleaning machine to participate in cleaning agent
Until the water temperature rose to about 40 DEG C, the UC-O3 parts cleaning agent in cleaning the pool (ordinary a 5 kg or so), slowly stir the water enable full dissolution (also at this time to start the sound or open air blowing installation stop stirring).
5 pretreatment of ultrasonic cleaning machine
Before cleaning should be used bamboo knife first parts surface dirt (such as dust cover either the surface there will be a lot of dust, cylinder parts in the shell curve will retention many thick and in addition to the sludge) simple clean in order to extend the cleaning liquid using life. Ultrasonic can stop cleaning fine, but the of mud of sewage disposal ability is weaker, so pre disposal should be as far as possible the yellow mud or dirt removal.
6 ultrasonic cleaning machine parts display
Put the parts in the reinforced basket quietly into the cleaning tank, when a lot of parts into a single, should try to make them in the basket in the average spread, do not stack.
7 ultrasonic cleaning machine boot
During normal operation of the ultrasonic cleaning machine, ultrasonic from three directions simultaneously transmit, initiated by the underside of the ultrasound, on both sides of the ultrasonic wave that has started, right rotation power conditioning knob, initiated by the underside of ultrasound. And screw it to the appropriate power. At this time, Leo appears is shown at the end of the ultrasonic power value.
8 ultrasonic cleaning machine down
In the cleaning process to stop, should be the first power knob to the minimum. And then press the stop bottom ultrasound. The cleaning time is controlled according to the condition of the cleaning appearance.
9 overflow of ultrasonic cleaning machine
If the cleaning tank level being too much oil. Should open the overflow of cleaning machine installation will remove to avoid secondary pollution cleaning workpiece. The detailed operation are as follows: open overflow discharge valve, injecting water or cleaning fluid to the cleaning pool until cleaning liquid began to overflow (Initiative for the scraper tool towards the direction of the overflow mouth cut oil coated to promote the rapid outflow), adhere to the overflow discharge valve normally closed to prevent accidents overflow the formation of air pollution.
10 ultrasonic cleaning machine after disposal
Remove cleaning parts, with the compressed air with the hole in the residual washing liquid completely blow net, and the appearance of dry (Initiative for the equipment the blowing dust gun with air compressor using). If the conditions, the best configuration in the washing machine near the pool. In order to remove the parts to stop rinsing.
11 ultrasonic cleaning machine cleaning agent
When the cleaning machine too many parts, the content of sludge cleaning agent may be quite high, coupled with ultrasonic emulsification. The cleaning agent will weaken the ability of cavitation, which is not suitable to continue to use. Suggested that the user to configure the water storage bucket and cleaning machine with the use of precipitation over dirty cleaning
12 assisted by ultrasonic cleaning machine
Many parts, such as cylinder head, piston, connecting rod, turbocharger, exhaust manifold etc. with these parts of coke, some lighter, is very easy to clean, but there are some very heavy, under this situation, the necessary soaking workpiece softening process will get better cleaning effect 1. Ultrasonic washing machine.
Please reference ultrasonic cleaning machine instructions, cleaning machine, electric control cabinet between the host and the temperature control sensor signal wire connection, ultrasonic drive line, heater control line line, and connect the 380VAC power, washing machine water pipe, a water outlet pipe and an overflow discharge tube.